6 Tips and Tricks with the Jamstik+ & SONAR

With the recent announcement of SONAR & Windows compatibility, the opportunity for connecting Bluetooth MIDI Controllers is now available with ease using Bluetooth 4.0. The jamstik is a five-fret guitar controller, designed small enough to fit in your backpack or carry-on. Here are five tips about the jamstik’s hardware and how it works within Sonar:

1. Navigate around the fretboard using the D-Pad

The jamstik was designed to fit in your backpack to be travel friendly, but it doesn’t mean you’re limited to a five fret note range! The D-Pad can remap the jamstik’s MIDI note output in real-time.

  • Remap in octave steps using the Up and Down buttons.
  • Remap in chromatic steps (virtual capo) using the Left and Right buttons.
  • Reset to default range (soft reset) by pressing Left and Right buttons simultaneously.

2. Single Channel versus Multi-Channel

When working with virtual instruments, you may find it seems as if the jamstik+ is only working on one string, the high E. Don’t panic. Your jamstik+ isn’t broken, and neither is the virtual instrument or your device. It’s likely that the virtual instrument is only recognizing input from MIDI Channel 1.

The jamstik+ defaults to outputting MIDI on channels 1 through 6 with the High E string outputting channel 1 and ending with the low E string as channel 6. This is the most uniform protocol for guitar MIDI controllers, but some software implements MIDI input differently. Some apps treat all incoming MIDI as one input regardless of channel implementation, and some apps even recognize multi-channel MIDI input to use it for multitimbral tracking or control. Being able to toggle between these two MIDI output modes on the jamstik, 6-channel and single channel, will enable the jamstik+ to control whichever protocol any app operates in.

You can also toggle the jamstik+ between 6-channel mode and single channel mode by using the D-pad. Press the Enter + Right button combo to go back and forth between the 6-channel default MIDI mode and Single Channel MIDI mode.

Single-Channel Toggle: Combo Command ENTER + RIGHT

3. The Mute Button

The mute switch is on the face of the jamstik, just behind the bridge.  The Mute Button sends MIDI Note Off messages for all active MIDI notes when pressed.

The jamstik also mutes active notes in two other ways; by lifting your finger off of a fretted note, or hovering your fingers over two or more frets simultaneously.

4. Use Tap Mode For Melodies!

The jamstik+ has a playing mode that doesn’t require picking, called Tap Mode. Tap Mode scans the fretboard for fingertip contact and ignores the pick detection completely. Tap Mode can be entered either momentarily by holding the center Enter button on the D-pad, or UP + DOWN to Toggle Tap Mode On or Off.

Tap Mode Momentary: HOLD ENTER & Play with left hand

Tap Mode Toggle ON/OFF: Combo Command UP & DOWN

5. String Bend Enable

The jamstik transmits Pitch Bend when any string is bent off of center. Sometimes it’s helpful to turn String Bend off if you find your fretting hand pulls or pushes the strings around enough that stray Pitch Bend messages are being transmitted. To toggle String Bend On or Off press Enter & Left button simultaneously.

String Bend Toggle: Combo Command ENTER + LEFT

6. A Few Tips For Optimizing Performance

Bluetooth MIDI performance greatly depends on your PC’s hardware specs & software settings. The Bluetooth refresh rate is rewarded by the operating system not by the controller, but there are some things we can do optimize the experience in software:
Here are a few considerations when using Bluetooth MIDI:

  • Reduce your buffer size: I recommend going low as you can for tracking without creating any jitter or popping in your audio output. Start with 128 samples and see how low your machine can handle.
  • Distance / Line of Sight: In our tests we found that the best performing scenarios are within line of sight of the device. Any walls or barriers can disrupt this, so if you’re looking to record from the other room you may want to experiment with placement of your device.
  • Preserve CPU Processing power - Especially on mobile builds, quit applications not being used.

With some of these tips and tricks, your workflow will go much quicker using SONAR & jamstik+ as your creation station. Ah, and don’t forget that since the jamstik is a class compliant MIDI controller, all of its buttons can be customized with the MIDI Learn function if available (we will save that for another blog post).

Stay tuned for much more from the Jamstik Team & SONAR in the upcoming weeks. If you like what you’re reading- then please share/spread the word! And of course, please post & share your creations on social media (Insta & FB), tag #Sonar #jamstik #MIDI #Bluetooth – we love to see what you are creating and we want to re-post!

Happy Playing,
Mike & The Jamstik Team

Published by

Mike Green [Zivix]

Mike is a guitarist/producer hailing from Minneapolis, MN. His initial dive into scene was his first metal record "Silence is Our Canvas" in 2009. He attended college at McNally Smith College of Music while playing with several original and corporate bands. Soon there after came touring, composing, and coordinating events. Mike's current groups are Audiyo Element (Rock/Hip-Hop), Ions and Atrophy (Instrumental Metal), and 8-bit composition project Dinbot. His musical path lead to involvement in the making of jamstik+ and PUC+ MIDI devices from Zivix, a music and technology company from Golden Valley, MN. Follow Mike on Instagram @mjgmusic